This
is a Hasegawa 1/200 Space Shuttle Orbiter with Boosters. I selected
"Discovery" for the Orbiter name. The whole model kit is about 30cm
tall, inclusive of the display base.
Click on
images below to see larger images
|
|
|
|
It
is to be noted that this kit is a re-issue from an old Hasegawa mold
(probably back in the early 90's), therefore, the External Tank (ET) lack some details of
the newer ETs as seen in more recent NASA photos. The centre "band"
should also have been corrugated but in this kit it was a raised band
instead. I had to scribe the lines on the band because they became too
faint, after some serious putty-ing and sanding work. One problem which I had
was the colour of the ET. The instruction says "brown" but I don't
like it to be so. From the NASA reference photos, the ET is a nice looking
combination of yellow-orange-tan of sorts (maybe after prolonged exposure to the
elements, at least looks better than brown!) that also varies in hue, depending
on the surrounding illumination. I had quite a hard time producing a mixture
of colours for the ET. I mixed orange, yellow, brown, red, white and
tan in different percentages using my eyes and a strong table lamp as visual
gauge, until I got the kind of colour that I wanted. A total of 3 different
custom-mixed colours were applied on the ET - base colour, darker shade of the
base colour and a light yellow-ish colour for the bands and patches on the
ET.
In this
kit, the 2 solid rocket boosters (SRBs) were molded together with the ET as a
single piece, albeit split into 2 halves - front and back. Fitting was not
as good as I would wish to, as the tips of the SRBs and the ET
cannot align together perfectly when attempting to join the 2 halves. Not
to mention that each half of the SRBs and the ET combination are held
together via 3 joints, with the centre joint being a long plastic slot
probably for strength, but is totally bogus since it doesn't exists in the
real thing! I ended up cutting and grinding off all the joint parts, so
that all the SRBs and ET parts are separated. Then I glue, putty, sand and apply
surfacer to each component until there are no visible seams and correct
any alignment problems. Lastly, I connected the SRBs to the ET back
together using custom-measured plastic styrene cards as joints, but now
without the "fictional" centre slot joint. A vernier calliper would be
helpful to record the position and gaps between the SRBs and ET before you
separate them; should you also decide to do what I did. You would need it
when re-producing the joints using styrene cards so that it would not be
too far off from the original. This is important because the display base
have molded-in studs to "hold" the SRBs at the bottom (you cannot
"shift" the studs to compensate as they are fixed).
Click on
images below to see larger images
|
|
|
|
The display base is a very
crude representation of the Mobile Launch Platform (MLP), but then, for the
price point of around SGD$40 for the whole kit (excluding the discount I got), I
think it's already a "bonus" to have a display base that roughly
resembles the MLP, which is still quite nice looking. Evergreen styrene
strips were added to the sides of the display base to enhance its edifice.
On the other hand, the real MLP is a very complex structure that deserves
to be rendered as a model kit by itself. A rectangular slant is molded
on the front of the display base for mounting a title plate should you
choose to (I will do it in future).
Some extra masking & painting work
were done overall to make it more realistic, but as the kit is quite
old, the painting instructions and decals did not provide for the
latest versions of the real Shuttle Orbiters. For example, the hinges of the
payload hatches are seen as small black rectangular patches, and the black
rectangular patches are longer for the front 2 hatches than for the rear 2
hatches. So I had to mask and paint them. The decal does provide options for
Atlantis, Endeavour and Discovery Orbiter names, but not Columbia and
Challenger.
Upon completion
of this project, I am quite satisfied with the result after all the efforts
invested. In my opinion, I think Hasegawa's kit has managed to capture the
shape of the Space Shuttle Orbiter's nose cone and the exterior areas
around the cockpit windows very nicely and quite accurately, despite at such a
relatively small scale. More details could have been wished for the provided
decals though.
Randy
Click on
images below to see larger images
|
|
|
|
|